Ruffled Keychain Fabric Key Fob

Finally – a tutorial for my Ruffled Keychain Fobs!!  They’re a fabric wristlet that hooks to your keys, so you can wear them on your wrist, grab them easily, etc.

I have been making these quite a while and always sell out of them when they’re listed in my Etsy Shop (I should probably stock that someday….)

I’ve been meaning to make a tutorial, and I finally kicked myself into gear.  THAT’s why there was no post this morning – I was anticipating a rare Saturday Tutorial post.  What, you didn’t even notice that I didn’t post this morning.. hmm. :)

So, on to the tutorial…

You’ll need a keychain clip thing – I don’t know what they’re called, but I think you can buy them in the “notions” section.  Then you’ll need 2 coordinating fabrics and some fusible fleece.

Cut one piece of ruffle fabric approximately 2 inches by 24 inches.  Cut the piece of fusible fleece about 1 inch by 10 inches.  If you don’t have fusible fleece, you can use regular fleece or flannel or anything to make it a little thick.  Cut one piece of the main fabric 1.5 inches by 5 inches.  Then cut 2 pieces of the main fabric about 2 inches by 12 inches.  Then one one end cut the curves like shown below:

Iron the square-ish piece into a narrow strip – fold up about 1/2 inch, iron it, then fold down about 1/2 inch and iron it, to give 2 nice edges:

Turn under the edges of the main pieces – the curves are  a little tricky, but just work slowly.  Iron the fleece onto one of them:

Grab your ruffle piece and finish the edges.  You can hem them.  I used my serger set on “P”  – – it’s like a not-so-dense rolled them:

 Then sew down the middle and gather the strip.  I talk about gathering on the Ruffled Hairclip Post.  It should be long enough to go from the end to where the curve starts:

Sew the ruffle down to the main fabric:

Then sew the two pieces of main fabric together along the side seams that you had turned under.  Be sure not to sew the ruffle down at the edge:

Alright, ready to assemble – – put on the clip thing, in the curve area, then fold it up like so:

And then fold the other end so it slightly overlaps – – my finger is in the way because I am bad at using pins – I just sew and go.  Anyways, zig zag over that seam to hold it in place:

Now, to make it look pretty, take the strip you made and wrap it around – tuck the end under itself to made a finished edge:

Then sew along the top and bottom edge of the strip – you can see my stitching below:

That’s it!!  I have one of these and I LOVE it!!  I can just slip it on my wrist and hold my keys that way when I run into the store, library, etc.  It’s also easier to find when I chuck it into my purse then just a small keychain.

This is a fun quick project – – – go make yourself one!! You can do it!!

Craft Blogger

Thanks for checking out this post from – – click on over to read it in its entirety – you’ll love it!

Thanks for Reading


  1. says

    I absolutely LOVE this!!! I have a lanyard that I have kept my keys and a phone pocket on. It’s clunky and annoying. I’ve wrapped it around my wrist, but again it’s clunky and annoying. I almost bought one of these the other day, but now I don’t have to!!! I can make it to lookk how I want it to look…and I even have the material! Thanks for posting!!!

  2. says

    This is so cute…I need more cute in my life and am always loosing my keys. May have to make one soon!

    Thanks for sharing on Show & Tell at SNAP!

    xoxo, Tauni

  3. says

    This is so cute…I need more cute in my life and am always loosing my keys. May have to make one soon!

    Thanks for sharing on Show & Tell at SNAP!

    xoxo, Tauni

  4. says

    This is so cute…I need more cute in my life and am always loosing my keys. May have to make one soon!

    Thanks for sharing on Show & Tell at SNAP!

    xoxo, Tauni

  5. says

    Where do you find those great fabrics for the keychains?? Is it a certain fabric line?? I love those fabrics and the combination of the fabrics.


  6. says

    Me too, she has great fabric lines. There are not copies of the pattern pieces are there? Whaen you make the pattern piece for the main piece, how do you make sure the indented parts are even- is there a trick for that?? Thanks again!!

  7. Holly McD says

    So I know this post is 2 years old, but maybe you’ll remember. :) The keychain clip do-dad…is the opening 3/4″? I just bought a couple of them, but the opening is 1″. I’m just wondering if I’ll need to make the little side indentions or not. Is your finished fob about 1″ wide? TIA!

  8. Tambara Stewart says

    I love this tutorial and I will definitely make one or maybe a few. Can you tell me where I can get the clips to go on bowties, I want to make them but not sure where to find the clips. Thanks


Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

CommentLuv badge